Connect with us

Articles

Creating Special Effects with High-Density Inks

Published

on

Clock_Interior_Detail

In garment printing, the term “special effects” covers a lot of inks and processes, some of which I’ve never considered to be part of this category. Puff, for example, isn’t a special-effect ink to me even though some consider it to be one. Others inks, such as discharge, have been around for a long time and are now being used in ways that do make them special effects. Then there are inks that are clearly designed for special-effect printing and that can create remarkable results when used correctly.

In garment printing, the term “special effects” covers a lot of inks and processes, some of which I’ve never considered to be part of this category. Puff, for example, isn’t a special-effect ink to me even though some consider it to be one. Others inks, such as discharge, have been around for a long time and are now being used in ways that do make them special effects. Then there are inks that are clearly designed for special-effect printing and that can create remarkable results when used correctly. I want to focus on some of my favorites in this article: high-density (HD) inks, gels, and bases.

If you aren’t familiar with HD inks, they can produce dramatic three-dimensional images. They are designed to print through very thick stencils and have a high viscosity with reduced tack and increased flow characteristics compared to standard plastisol inks. As you’ll see in this article, they can achieve thick ink deposits with extremely sharp edges. Used correctly and creatively, HD inks allow you to produce truly unique effects.

Although HD inks were very popular for quite a number of years, they quieted down because of concerns and regulations over the use of ortho-phthalates. Now that many of the ink companies have reformulated, HD inks are back again, but few printers use them because many don’t know how. The ultimate goal with HD inks is to produce a print that has dimension to it after printing and that stays that way once it’s through the curing unit. I’ll discuss the production steps that are unique to HD printing below and show how the technology was used to create several award-winning shirts.

Screenmaking Considerations
One of the most common problems I see in shops that aren’t accustomed to HD printing is screenmaking, especially selecting the right mesh and creating stencils of sufficient thickness to achieve the desired effect. You need a thin mesh that has a good percentage of open area to allow the ink to pass through the stencil easily without too much squeegee pressure. The most popular meshes for HD printing are around 80 to 83 threads per inch with a 70-71-micron “S” thread. These meshes have an open area of about 60 percent.

You can make stencils for HD printing with certain types of direct emulsions or with thick capillary films. I’ve worked with both, and my opinion is that capillary films definitely make more sense for this application. The issues I have with direct emulsions are the time it takes to apply them, the number of coats it takes to get the needed thickness, and the difficulty of duplicating the results across multiple screens, which takes a high-quality coating machine to do predictably. Capillary films are easier to apply and you can get them in thicknesses ranging from 100 to 1000 microns. The most popular films for HD printing fall between 200 and 400 microns. Thicker films might require you to use wire meshes with 80-micron threads and will require very long exposure times. It’s also very difficult to get good, clean prints from such thick ink deposits.

Advertisement

Applying the capillary film to the mesh is where many printers run into problems. Often, they use water to apply the mesh as they do when making screens for their regular work, but it’s not the right choice for HD printing. For one, the water will reduce the thickness of the stencil and therefore the ink deposit. Also, because the capillary films used for HD printing are so thick, water doesn’t always adhere them to the mesh very well and they can delaminate from it during the printing process. For this application, use direct emulsion instead of water to apply the capillary film. I prefer using SBQ-sensitized pure-photopolymer films and emulsions for HD screens.

Step-by step instructions are explained in “Making Screens for HD Printing.” A few important points:

• The cost of the films is fairly high, so when possible, I cut the films down to size leaving a 1-inch border on all sides of the image area.
• To get the best results, I apply emulsion twice. I use a squeegee with the first coatings to attach the film, as shown in the sidebar, and then I apply a double coat of the same emulsion to the inside of the screen using a round-edge scoop coater to ensure a good bond between the film and emulsion. You can dry the screen between the two steps if you like, but it isn’t necessary.
• Be sure the screen is dry before exposing it, remembering that you are creating a very thick stencil. With a heated drying cabinet, depending on the settings and the humidity in the screenroom, it should take about an hour. It will take several hours without a heated cabinet, and you might consider letting the screen dry overnight.
• Avoid using weak light sources to expose thick-film screens. You might be able to get such an exposure unit to work, but the exposure times will be very long and the edge definition will probably not be as good. I prefer using metal-halide lamps in the 3K to 6K range. When using one of these, I allow 90 seconds for each 100 microns of film thickness, so a 400-micron film would take 6 minutes to expose. I haven’t tried using one of the new LED exposure systems to expose high-density screens, but I’m told they work fine.
• After exposing the screen, I like to let it soak in a dip tank filled with water for about 5 minutes. This isn’t necessary, but will make it easier to wash out the screen.
• For screen washout, I use a 1000-psi pressure washer with a little V-shape to the nozzle from about a foot away. Wash only the side that has the film attached to it. After washing is complete, dry the screen. I prefer vacuuming my screens dry.

Ink Selection and Job SetupCreating Special Effects with High-Density Inks
There are several different types of HD formulations — inks, gels, and bases. HD inks can be used straight out of the can and produce extremely sharp, well-defined edges. The most common colors are black and white; they can be mixed with other colors to create secondary colors. After curing, inks should retain their sharpness and have a matte finish.

HD gels are similar to inks and are available as a clear; they are also available with metallic or other particles in them, such as the silver gel shown at right. When printed, they may or may not have dimension and sharp edges, depending on the gel you use. When fully cured, they should be glossy Creating Special Effects with High-Density Inkswith rounded edges, as the detail of the print on the left shows.

Bases usually require toner or ink to be added for color. So many HD bases are available that it’s difficult to give a blanket description of what they do. Some rise like puff inks while others have a very hard finish that won’t flatten when foil is applied through a transfer machine, like the print shown on the right.Creating Special Effects with High-Density Inks

Advertisement

Since these are all three-dimensional inks, you should set your off-contact distance higher than you would for a standard print. If you are printing multiple HD colors in a job, set each screen a little higher than the previous one to avoid the ink not clearing the screen. For jobs that involve standard plastisols with HD effects, print the HD colors last.

In all types of HD printing, use soft squeegees with minimal pressure. I like to use a 55/90/55 triple-durometer squeegee whether printing on an automatic or manual press. Use a deep squeegee angle and just enough pressure to clear the screen. One stroke is best as a second stroke can cause the ink to spread under the screen and smear. You can get a wonderful textured effect in your print by using a wallpaper brush instead of a squeegee and Creating Special Effects with High-Density Inkscutting the bristles down (see left). This is easiest when printing by hand, of course, but you can also trim the handle in addition to the bristles and then clamp the brush into the squeegee holder to print on an automatic. The print on the right shows a close-up shot of a print with a silver gel onto an HD black ink that was done using this technique.

Some HD inks are very thick when printed, but surprisingly, they flash fairly quickly, not unlike standard plastisol inks. I prefer using an IR flash unit when printing manually and a quartz unit on an automatic. The temperature needed to fully cure HD inks ranges from 325 to 380 F through the entire ink layer. Because of the thickness of the ink deposit, in addition to raising the temperature, you’ll need to slow down the conveyor of your curing unit as well to get enough heat through the print to fuse the ink.

Remember what I mentioned earlier about the different finishes of HD inks and gels after Creating Special Effects with High-Density Inkscuring. Inks should have a matte finish with sharp edges. If they are glossy after curing, chances are the temperature was too high. Gels, on the other hand, should have a glossy finish with rounded edges when they are fully cured. If they are undercured, they will look just like an HD ink, with a matte finish and sharp edges.

HD special effects require a lot of heat, so white shirts may not be the best choice for this work as they could easily scorch. Dark-colored shirts are definitely more forgiving. When printing a lot of complex layers, use a hand-held heat gun to carefully gel the inks as a flash may get too hot in one area and cause a problem.

Get Creative
Most of the shirts for this article were done by European T-Shirt Factory, Istanbul, Turkey, a very capable, high-volume producer of printed apparel. (The shirts illustrating effects with gel inks and foil were done during a workshop.) These shirts were created for technical printing competitions and were designed to test the limits of HD technology, not to produce wearable garments. But the company does a lot of production work with HD effects as well, and these award-winning shirts suggest what this technology is capable of with a little creativity. With experience, I’m sure you’ll grow to love HD inks for special-effects work as much as I do.

Advertisement

Advertisement

SPONSORED VIDEO

Let’s Talk About It

Creating a More Diverse and Inclusive Screen Printing Industry

LET’S TALK About It: Part 3 discusses how four screen printers have employed people with disabilities, why you should consider doing the same, the resources that are available, and more. Watch the live webinar, held August 16, moderated by Adrienne Palmer, editor-in-chief, Screen Printing magazine, with panelists Ali Banholzer, Amber Massey, Ryan Moor, and Jed Seifert. The multi-part series is hosted exclusively by ROQ.US and U.N.I.T.E Together. Let’s Talk About It: Part 1 focused on Black, female screen printers and can be watched here; Part 2 focused on the LGBTQ+ community and can be watched here.

Promoted Headlines

Most Popular